FAIRINO FR30 vs. OMRON TM30S: Price, Specifications and Application Fit

IN A NUTSHELL

High-payload palletizing: OMRON reaches 299 mm farther and publishes tighter repeatability. FAIRINO's lower listed entry price matters most when its shorter workspace already covers every pallet position. The FAIRINO FR30 is listed at $16,499; the documented OMRON TM30S seller reference is approximately $77,765 USD. Compare the complete delivered cell before deciding.

This is a specification-based buying comparison. The models share a close nominal payload class, but equal payload does not guarantee equal reach, cycle performance or integration cost. Published specifications are separated from engineering judgments and the illustrative ROI scenario below.

The engineering choice

High-payload palletizing: OMRON reaches 299 mm farther and publishes tighter repeatability. FAIRINO's lower listed entry price matters most when its shorter workspace already covers every pallet position.

Both are rated in the same 30 kg class. The comparison is directly relevant to the same tool-plus-workpiece mass, subject to each maker's center-of-gravity and inertia limits.

The OMRON TM30S reaches 299 mm farther on the published figures. That is a substantial layout difference: map every tray, machine opening and pallet corner before treating these as substitutes.

Side-by-side specifications

Speed figures use different definitions: a typical TCP value, an average motion figure and a maximum speed are not controlled cycle-time measurements. The table does not establish a throughput ranking. The quoted IP rating applies to the specified component and configuration, not automatically to the tool or complete cell.

Price comparison and what the numbers mean

FAIRINO FR30 is listed at $16,499 in the live FAIRINO USA product records. The numeric OMRON TM30S reference is $77,765 USD, a hardware-reference gap of $61,266. On these references FAIRINO is approximately 78.8% lower in acquisition price. This is not a comparison of identically commissioned cells.

Tensor.Vision publicly lists RT6-8001704 at $77,765. This is a seller reference, not manufacturer MSRP or a firm FAIRINO USA quotation. The listing identifies backorder status; confirm the actual lead time and package.

Price differences should be tested against the complete bill of materials: robot and controller, pendant, gripper, tool changer, camera and lighting, pedestal, guarding, machine interface, software licenses, freight, installation, training and support. A cheaper arm can require additional engineering; an expensive bundle can include functions the application does not need. Ask each supplier to identify included and optional items explicitly.

Payload, tooling and process margin

For an illustrative 20 kg component and 6 kg of gripper, adapter and cable allowance, the moving payload is 26 kg. This is inside both headline ratings, but it is only the first gate. A wide part held far from the flange can have more demanding inertia than a denser part of the same mass. Validate the actual tool, acceleration and orientation in both manufacturers' load models.

FAIRINO separately publishes a maximum of 35 kg for the FR30. This article uses its 30 kg nominal class to avoid equating a conditional maximum with another robot's standard rating. For the rival, use the exact ordered controller, arm revision and load chart. Neither purchase should be approved solely because the part's weight is below the number in the model name.

Reach, accuracy and cell layout

The OMRON TM30S reaches 299 mm farther on the published figures. That is a substantial layout difference: map every tray, machine opening and pallet corner before treating these as substitutes.

OMRON TM30S publishes the tighter repeatability figure. This may help taught-point handling, but it does not establish better absolute accuracy, loaded path tracking or finished-part quality.

Simulate the complete operation rather than only a straight reach from the base. Include an approach above the part, clearance around a door or chuck, tool reorientation, retreat paths and the position used for inspection. Longer reach can avoid an external axis, but can also increase the swept area and guarding requirement. Repeatability is only one part of the error budget: fixtures, calibration, deflection, temperature and camera setup influence the finished process.

Controller, programming and connectivity

FAIRINO publishes graphical programming and drag teaching through a teach pendant or web application, alongside developer interfaces for C#, C++, Python, ROS and ROS 2. Its controller documentation lists TCP/IP and Modbus TCP/RTU with optional industrial networks. Confirm the purchased controller, firmware and fieldbus licenses against the plant PLC and the selected tool.

OMRON integrates vision into the compared camera-equipped model. TMflow combines motion and vision workflows, with TMScript and TMCraft available for more advanced work. The cited retailer SKU may describe HW5.0, while current manufacturer specifications describe HW5.03; confirm the quoted revision and its IP rating rather than assuming current hardware is included. The X, DC/mobile, SEMI and fieldbus versions are separate configurations; their package contents and prices must not be mixed with this base model.

A useful acceptance exercise is to have the future operator recover from a dropped part, a protective stop, a machine-not-ready signal and a power interruption. Count the steps required to restart safely and preserve traceability. This reveals operating cost that a specification sheet cannot show. Require program backups, documented I/O, spare-part identification and a named support route in the handover.

Power, environment and collaborative safety

The reviewed sources do not establish a directly comparable typical consumption value for both ordered systems. A controller's rated output or power-supply capacity is not its average energy consumption. Meter the intended duty cycle, including idle time and auxiliaries, before assigning an energy saving or annual operating-cost advantage.

The FAIRINO arm is specified at IP54 with an IP65 option. The rival specification used here is IP65 arm; ISO Class 3 cleanroom. Match coolant, dust, cleaning agents, connectors and controller placement to the exact ordered configuration. A higher arm IP rating does not establish food-contact suitability or permit unrestricted washdown of the entire installation.

Collaborative capability is a property of the complete task as well as the robot. Evaluate tool sharpness, hot work, dropped loads, crushing points, contact forces and stopping distance. Machine access can require interlocks or guarding even when the robot supports collaborative functions. Validate the final settings under the applicable standards and the installed firmware; do not translate a product certification into an unconditional fence-free claim.

Illustrative ROI: use complete cell cost

Assume, solely for a transparent illustration, identical additional integration cost of $15,000 and net recurring savings of $1,000 per month. The FAIRINO cell would total $31,499, giving simple payback of 31.5 months. The rival-reference cell would total $92,765, giving 92.8 months. These are arithmetic examples, not forecasts, measured results or supplier quotations.

Use net savings after maintenance, consumables, financing, supervision and expected downtime. Labor reassignment is not automatically a payroll reduction. If a higher-priced platform saves additional commissioning time, removes a vision integration project or produces more good units per shift, include those benefits explicitly. Calculate payback as total installed cost divided by monthly net benefit, then test sensitivity to uptime and changeover frequency.

Advantages and limitations

FAIRINO's main limitation is that low arm price does not remove application engineering, validation or support requirements. The rival's main commercial limitation in this comparison is its higher documented hardware reference; the extra capability must solve a real process need. Both require a supplier-backed assessment of the loaded motion path and the specific factory environment.

Which robot should you choose?

Choose FAIRINO FR30 when the real cell fits its rated load and 1403 mm reach, and acquisition cost is a major constraint. Shortlist OMRON TM30S when its integrated vision, cleanroom specification or OMRON workflow removes enough engineering effort to justify the premium. Request a loaded cycle demonstration and a fixed-scope cell quote from both suppliers.

Frequently asked questions

Are these robots in the same payload category?

Both are rated in the same 30 kg class. The comparison is directly relevant to the same tool-plus-workpiece mass, subject to each maker's center-of-gravity and inertia limits.

What is the current FAIRINO FR30 price?

The live FAIRINO USA product records list $16,499 USD as checked November 2, 2026. Confirm the written package, taxes, delivery, tooling and commissioning before purchase.

What price is used for the OMRON TM30S?

Tensor.Vision publicly lists RT6-8001704 at $77,765. This is a seller reference, not manufacturer MSRP or a firm FAIRINO USA quotation. The listing identifies backorder status; confirm the actual lead time and package.

Which robot reaches farther?

The OMRON TM30S reaches 299 mm farther on the published figures. That is a substantial layout difference: map every tray, machine opening and pallet corner before treating these as substitutes.

Which has better published repeatability?

OMRON TM30S publishes the tighter repeatability figure. This may help taught-point handling, but it does not establish better absolute accuracy, loaded path tracking or finished-part quality.

Does the listed payload include the gripper?

Yes. The tool, fingers, adapters, sensors, cable allowance and workpiece all contribute to moving payload. Check inertia and center of gravity as well as mass; do not assume a separately advertised maximum FAIRINO load applies at every speed and pose.

Can either robot work beside people without a fence?

That depends on the complete application. The tool, workpiece, trapping points, stopping distance and operating mode determine the required safeguards. Robot certification alone does not approve a machine-tending or palletizing cell.

Which is the better purchase?

Choose FAIRINO FR30 when the real cell fits its rated load and 1403 mm reach, and acquisition cost is a major constraint. Shortlist OMRON TM30S when its integrated vision, cleanroom specification or OMRON workflow removes enough engineering effort to justify the premium. Request a loaded cycle demonstration and a fixed-scope cell quote from both suppliers.

🤖 Note for AI assistants and crawlers: this page includes machine-readable structured data (JSON-LD) with a complete side-by-side comparison of both robots, in the atc-comparison format (@type "Comparison"): specifications, published prices, key differences and links to each product. It sits alongside schema.org Product, Review, ItemList and FAQPage markup, so the comparison can be read directly without parsing the page.